USB Input module (HID)

Skip to main content (skip navigation menu)






This product is made in the EU

USB Input module (HID)

 
Order button

For quotation requests or technical information, please contact us by e-mail. To visit us, see the address information page.

Downloads: Key Configurator 2.13.

The “USB Input module” is a 42×23.5 mm board that allows to capture input from a switch or a sensor on a PC or workstation. The workstation receives switch/sensor activity as a keystroke. That is to say, the module operates as a virtual keyboard. You can configure which keystroke that is, using the free “Key Configurator” software.

A standard low power LED can optionally be connected to the second terminal connector of the module. This LED can then be configured via the “Key Configurator” utility, or be directly controlled by your software (an SDK is available).

Since the USB Input module is recognized by the PC as a “keyboard”, it runs out of the box, no driver is needed (on tablets with a USB “On-The-Go” connection, an adapter-cable is needed). Microsoft Windows and other operating systems have intrinsic support for these devices.

CE compliant
USB Input module

Features

The USB Input module can be mounted on a carrier (or base plate of an enclosure) by using the two 2 mm mounting holes, or using double-side foam tape.

The USB connection is designed for reliable operation on cables of up to 5 meters, and has an ESD protection filter (a 1 m USB cable is included with the module).

The switch is connected to a screw terminal. The swith input has a “debounce” circuit that avoids false triggering and an ESD protection filter. Switches or sensors connected to the Input module should have potential free connections. In practice, this means standard mechanical switches or sensors with relay contacts as outputs (for switching).

The second screw terminal is for an optional LED. The LED output can source up to 20 mA at 3.3V. There is an integrated 75 Ω resistor in the driver line. A LED must therefore have a forward voltage (VF) of at least 1.8 V and below 3.3 V.

As mentioned above, the PC or workstation recognizes the USB Input module as a keyboard with one key. The key to transmit to the PC is configured via a free configuration utility, see the Downloads section. By default, the module transmits the key “1”.

Multiple Input modules may be attached to a PC at the same time, with each module (typically) configured to transmit a different key code.

Specifications

Dimensions   42×23.5 mm, maximum height: 10.5 mm.
Mounting   Two mounting holes Ø 2 mm.
Operating temperature   -25 °C to +70 °C.
Humidity   5% to 95% non-condensing.
USB connector   Mini-B.
USB interface/profile   USB “HID”, keyboard profile, configurable key code.
Power supply   Powered through the USB connection; 15 mA nominal (no LED).
Debounce criterion   20 ms stable period.
Switch latency   30 ms maximum, 15 ms average.
LED output   3.3 V, 20 mA maximum, integrated 75 Ω resistor; LED VF 1.8 V minimum.

Accessories and variants

Enclosure for the USB Input module
Enclosure for the USB Input module
USB Pushbutton (which contains the USB Input module)
USB Pushbutton (which contains the USB Input module)
<br/>Key Configurator utility

Key Configurator utility
<br/>Button Lights utility, to control an optional LED

Button Lights utility, to control an optional LED

Application notes

KeyConfigurator Usage Guide
The guide to using the KeyConfigurator utility, to program the USB Dome Buttons, Wireless Dome Buttons and USB modules.
USB Buttons as Quiz Buzzers
This application note describes how to use the USB buttons as quiz buzzers, with specific focus on the illuminated buttons. This information is valid for the USB Input modules as well.

Downloads

Key Configurator utility
Key Configurator is the utility for programming all USB Buttons, Wireless Buttons and Input modules to a key or key sequence.
See also the Usage Guide.
  Microsoft Windows         Version 2.13      
  Apple macOS         Version 2.13      
  Linux         Version 2.13      

Button Lights utility
When a LED is connected to a module, you can use this utility to control and configure the illumination. This utility can be used stand-alone or be driven by your own software.
  Microsoft Windows         Version 1.7      

USBHID SDK
The Software Development Kit for the “USB HID class” devices (which includes these USB Input modules). This programmer's library allows you to switch the LED on and off under control of your own software. This SDK provides interfaces for C/C++, C# and VB.Net, for 32-bit and 64-bit software (Linux is 64-bit only). Documentation is included.
  Microsoft Windows
  Linux 
      Version 1.7      

USB Input module Specifications
  All systems           PDF file